Director of the Research and Development Center “The Republican Proving Ground for Mobile Machines Testing” KOT Sergey Anatolyevich
R&D Center “The Republican Proving Ground for Mobile Machines Testing” is accredited by the National accreditation system of the Republic of Belarus in compliance with STB ISO IEC 17025, it is a Testing Center E 28/Q under 1958 Geneva accord, it was included on the Unified Registry of certification authorities and test laboratories (centers) of the Customs Union, carrying out assessment of compliance of products with the Technical Regulations of the Customs Union.
Address physical: 5 km of MKAD, house 23 (the outer side of MKAD (M9), a congress at the glazed bridge (opposite the micro-district Angarskaya). Coordinates: 53.897799, 27.702019
Main areas of activities
Carrying out of certification tests of all categories of vehicles to obtain the certificates of conformity, the reports concerning the regulatory approval of vehicle type with regard to individual properties pursuant to the UN Rules and vehicles type approval to release on the territory of the Customs Union. Tests are carried out to be compliant with the requirements of the following international and national standards:
UN Rules
STB, GOST and GOST R
Technical Regulations of the Customs Union 018/2011 “On the safety of wheeled vehicles”
Technical Regulations of the Customs Union CU 010/2011 “On the safety of machinery and equipment”
Technical Regulations of the Customs Union CU 007/2011 “On the safety of products for children and adolescents”
Research and testing of experimental and production models of vehicles, systems, vehicles constructional elements and developing of recommendations to improve their performance properties in compliance with the current and future requirements
Verification of the requirements to individual vehicles prior to their release into circulation
Verification of the requirements to vehicles in service in case of changes in their engineering design
Assigning and application of the vehicle identification number (VIN)
Proving roads plan
1
Field for geometric measurement and inspection of vehicle structure, light alarm illumination device, rear view mirrors, visibility from the driver's seat
2
Field for maneuvering tests (flexibility into the back passage)
3
Field with basalt coating for evaluation of braking performance
4
Field for measurement of control speedometers maximum speed
5
Field for stability and handleability tests
6
Field for measurement of traction and dynamic properties and fuel consumption
7
Lifts for parking brake system tests
8
Field for audio measurement, audible signaling
9
Fields for tests of handling and stability in critical driving conditions
10
Field for tests of steering control of vehicles towing trailers
11
Field for tests of four-wheel drive machines steering control
12
Field for tests of mobile machines steering control
13
Laboratory-household unit
14
Garage for machine preparation to tests
Certification of motor vehicles
Certification tests of motor vehicles are conducted on the basis of a decision by the Certification Authority. The applicant is required to send an application indicating the test object and a list of properties for which it is necessary to conduct tests. The application is required to be enclosed with Technical descriptions of the properties, according to the application, as well as general technical description of the vehicle.
Application form
Verification of the requirements to individual vehicles prior to their release into circulation
As an applicant stands a vehicle manufacturer or his authorized representative acting on his behalf, or any person carrying vehicle imports to the single customs territory of the Customs Union, or his representative.
• Upon the examination of a vehicle, manufactured in a member state of the Customs Union under the conditions of mass production, which is constructed and individually modified by the agreement with the vehicle manufacturer before the release into circulation, as a manufacturer's representative serves a person carried out the introduction of these changes in vehicle design.
• Upon the examination of a vehicle, released into circulation from the previous state defence order, as an applicant stands a person carried out the release of the vehicle into circulation.
Conformity assessment of a single vehicle is conducted as follows: 1) submission of an application and a set of required documents 2) decision-making on the application within three working days 3) identification of a single vehicle 4) verification of compliance with the requirements provided for in paragraphs 11–14 and addendums №№ 4–6, paragraph 4 of addenda 7 TR CU 018/2011 “On the safety of wheeled vehicles” by the technical expertise of design and, if necessary, tests1 5) preparation of record of vehicle’s construction technical expertise 6) execution of vehicle safety certificate and its assignment to the applicant
In case of non-conformity of a single vehicle with Technical Regulations of the Customs Union 018/2011, the vehicle can be brought into compliance and submitted to the laboratory for reassessment of compliance.
If a single vehicle is of the type for which approval is valid, thus the Motor Vehicle Safety Certificate is executed on the basis of this approval of a vehicle type
Application form
The list of required documents
1The records of tests conducted in an accredited testing laboratory can be used as evidentiary materials confirming the compliance of a single vehicle requirements specified in Annex 4–6 to this technical regulation. If an applicant provides a regulatory approval of the vehicle type contained in the UN regulations № 10–12, 14, 16–18, 21, 26, 34, 39, 46, 48, 58, 73 and 107, the technical expertise on the relevant sections of the application № 4 to this technical regulation is not carried out.
Verification of the requirements to vehicles in service in case of changes in their design (modifications of vehicles)
The objects to verification are vehicles issued in circulation and passed the state registration with changed design (construction) parameters or components.
An introduction of changes in the design of a vehicle and subsequent verification of compliance with the requirements of technical regulatory legal acts that establish requirements for vehicles with regard to road safety are carried out under the permission and under the control of the Driver Licensing Office of the Road Safety Unit at the place of registration of the vehicle.
As an applicant stands a vehicle owner or his authorized representative acting on his behalf.
An applicant must apply to the Driver Licensing Office of the Road Safety Unit at the place of registration of the vehicle and receive a referral for the technical expertise of the modified vehicle.
Submit an application to the R&D Center “The Republican Proving Ground for Mobile Machines Testing”.
Provide a vehicle for the technical expertise of the design, carrying out the necessary tests and measurements at R&D Center “The Republican Proving Ground for Mobile Machines Testing” at the agreed time. The vehicle should be clean and in a technically sound condition.
In case of non-conformity of a vehicle with technical regulatory legal acts, that establish requirements for vehicles with regard to road safety, the vehicle can be brought into compliance and submitted to the laboratory for reassessment of compliance.
According to the results of the technical expertise of the vehicle’s design (construction), tests and measurements, a protocol of scientific and technical expertise (tests) of the modified vehicle and a statement on conformity of the modified vehicle with safety requirements are drawn up, and then passed to the applicant.
Application form
List of the required documents
Verification of compliance with the requirements to a single vehicle manufactured individually with technical creativity before the release into circulation
As an applicant stands a vehicle manufacturer or his authorized representative acting on his behalf.
The applicant is required to submit the following documents:
Application
General technical description of the vehicle
Declaration on the quantity and quality of the work performed in the manufacture of the vehicle
Personal identity document of the applicant/certificate of state registration
Conformity assessment of a single vehicle manufactured individually with technical creativity is conducted as follows: 1. Submission of an application and a set of required documents 2. Decision-making on the application within three working days 3. Verification of compliance with the requirements provided for in paragraphs 11–14 and addendums №№ 4–6, paragraph 4 of addenda 7 TR CU 018/2011 “On the safety of wheeled vehicles” by the technical expertise of design and, if necessary, tests 4. Assignment and application of the vehicle identification number (VIN), processing and fixing of the license plate on the vehicle 5. Preparation of record of vehicle’s construction technical expertise 6. Execution of vehicle safety certificate and its assignment to the applicant
In case of non-conformity of a single vehicle with Technical Regulations of the Customs Union 018/2011, the vehicle can be brought into compliance and submitted to the laboratory for reassessment of compliance.
Application form
Assignment and application of the vehicle identification number (VIN)
In compliance with Paragraph 3 of the Technical Regulations of the Customs Union 018/2011 “On the safety of wheeled vehicles” each vehicle has a unique identification number (VIN).
The Research and Development Center “Republican Proving Ground for Mobile Machines Testing” is authorized to assign and apply the Vehicle Identification Number (VIN) on the vehicles manufactured individually with technical creativity, as well as on the vehicles in service in case of loss of the identification number.
Assignment and application of the vehicle identification number (VIN) on single vehicles manufactured individually with technical creativity are conducted during the verification of compliance with the requirements to vehicles before their release into circulation.
Assignment and application of the vehicle identification number (VIN) on the vehicles in service in case of loss of the identification number are conducted by the assignment of the Interdistrict Registration-Examinational Office of the State Automobile Inspectorate at the place of registration of the vehicle.
As an applicant stands a vehicle possessor or his authorized representative acting on his behalf.
To get the assignment and application of the vehicle identification number (VIN) an applicant is required to submit:
Application for the assignment of the VIN code in replacement of the lost one
The assignment of the Interdistrict Registration-Examinational Office of the State Automobile Inspectorate
Personal identity document of the applicant/certificate of state registration
Vehicle Registration Certificate
Application form
Additional services
Test drive organizing and conducting
Club events and presentations
Organizing and conducting sports and training activities
Contacts
Sergey A. KOT, Director of the Research and Development Center “Republican Proving Ground for Mobile Machines Testing”
+375 (17) 332 63 90
avtopoligon@oim.by avtopoligon@tut.by
Sidorenko Dmitriy Nikolayevich, Deputy director on expert examination
+375 (17) 332 63 94
Submit of requests
+375 (17) 332 63 91
Department of Technical Expertise
+375 (17) 385-97-31
csimm@oim.by csimm@tut.by
Department of road tests
+375 (17) 385-97-32
csimm@oim.by csimm@tut.by
Legal address: 12 Akademicheskaya str., 220012, Minsk, Republic of Belarus
Actual address: The outer side of the MKAD (M9), the 6th km, the crossover track at the glazed pedestrian bridge (opposite to the Angarskaya microdistrict). Geographic coordinates of the entrance gates 53°53'52.15 "N; 27°42'07.47 "E.
View on map
SCHEDULE
Monday – Thursday
8.30 – 17.30
Friday
8.30 – 16.15
Closed for lunch
13.00 – 13.45
Saturday – Sunday
Closed
Сontacts
12 Akademicheskaya str., 220072 Minsk, Republic of Belarus
